Other config attributes for Portsother_config : priority-tags: optional
stringeither true or false An 802.1Q header contains two important pieces
ofinformation: a VLAN ID and a priority.other_config : bond-hash-basis:
stringcontaining an integer An integer hashed along with flows when choosing
outputslaves in load balanced bonds. When changed, all flows will beassigned
different hash values possibly causing slave selectiondecisions to
change.other_config : bond-detect-mode: optional stringeither miimon or carrier
The means used to detect link failures. Defaults tocarrier which uses each
interface's carrier to detect failures.When set to miimon, will check for
failures by polling eachinterface's MII.other_config : bond-miimon-interval:
optional stringcontaining an integer The interval, in milliseconds, between
successiveattempts to poll each interface's MII. Relevant only
whenother_config:bond-detect-mode is miimonother_config : lacp-system-id:
optional stringThe LACP system ID of this Port. The system ID of a LACP bondis
used to identify itself to its partners. Must be a nonzeroMAC address. Defaults
to the bridge Ethernet address if unset.other_config : lacp-system-priority:
optional stringcontaining an integer, in range 1 to 65,535 The LACP system
priority of thisPort. In LACP negotiations, link status decisions are made
system with the numerically lower priority.other_config : lacp-time: optional
stringeither slow or fast. The LACP timing which should be used on this Port.
defaultslow is used. When configured to be fast LACP heartbeats arerequested at
a rate of once per second causing connectivityproblems to be detected more
quickly. In slow mode, heartbeatsare requested at a rate of once every 30
seconds.other_config : lacp-fallback-ab: optional stringeither true or false
Determines the behavior of openvswitch bond in LACP mode.If the partner switch
does not support LACP, setting thisoption to true allows openvswitch to
to active-backup.If the option is set to false, the bond will be disabled.In
both the cases, once the partner switch is configuredto LACP mode, the bond
use LACP.other_config : bond-rebalance-interval: optional string,containing an
integer, in range 0 to 10,000 For a loadbalanced bonded port, the number of
milliseconds betweensuccessive attempts to rebalance the bond, that is, to
moveflows from one interface on the bond to another in an attemptto keep usage
of each interface roughly equal. If zero, loadbalancing is disabled on the bond
(link failure still causeflows to move). If less than 1000ms, the rebalance
intervalwill be 1000ms.other_config : stp-enable: optional stringeither true or
false. If spanning tree is enabled on the bridge, member ports areenabled by
default (with the exception of bond, internal, andmirror ports which do not
with STP). If this column'svalue is false spanning tree is disabled on the
port.other_config : stp-port-num: optional stringcontaining an integer, in
1 to 255 The port number used for the lower 8bits of the port-id. By default,
the numbers will be assignedautomatically. If any port's number is manually
configured ona bridge, then they must all be.other_config : stp-port-priority:
optional stringcontaining an integer, in range 0 to 255 The port's relative
priority valuefor determining the root port (the upper 8 bits of the
port-id).other_config : stp-path-cost: optional stringcontaining an integer, in
range 0 to 65,535 Spanning tree path cost for theport. A lower number indicates
a faster link. By default, thecost is based on the maximum speed of the
link.other_config : rstp-enable: optional stringeither true or falseIf rapid
spanning tree is enabled on the bridge, member portsare enabled by default
the exception of bond, internal,and mirror ports which do not work with RSTP).
If thiscolumn's value is false rapid spanning tree is disabled onthe
port.other_config : rstp-port-priority: optional stringcontaining an integer,
range 0 to 240 The port's relative priority valuefor determining the root port,
in multiples of 16. By default,the port priority is 0x80 (128).other_config :
rstp-port-num: optional stringcontaining an integer, in range 1 to 4,095 The
local RSTP port number, usedas the lower 12 bits of the port-id.other_config :
rstp-port-path-cost: optional stringcontaining an integer The port path cost.
The Port's contribution, when itis the Root Port, to the Root Path Cost for the
Bridge.other_config : rstp-port-admin-edge: optional stringeither true or
falseother_config : rstp-port-auto-edge: optional stringeither true or false
auto edge port parameter for the Port. Defaultis true.other_config :
rstp-port-mcheck: optional stringeither true or false The mcheck port parameter
for the Port. Default is false.other_config : mcast-snooping-flood: optional
stringeither true or false If set to true, multicast packets areunconditionally
forwarded to the specific port
This class represents the following YANG schema fragment defined in module ovsdb
list port-other-configs {
key "other-config-key";
leaf other-config-key {
type string;
}
leaf other-config-value {
type string;
}
}
The schema path to identify an instance is
ovsdb/ovsdb-port-interface-attributes/port-other-configs
To create instances of this class use PortOtherConfigsBuilder
.